Trident

Auramix 400 is a unique combination of the latest generation superplasticisers, based on a polycarboxylic ether polymer with long lateral chains. 

Additional Information:

• Production Capacity: 1000
• Delivery Time: 1-10 days as per availiblity
• Packaging Details: Auramix 400 is available in 200kg and 250kg drums

Being one of the trusted firms in the industry, we are highly engaged in providing a unique range of Conplast SP 430 DIS.

Uses:

• To provide excellent acceleration of strength gain at early ages and major increases in strength at all ages by significantly reducing water demand in a concrete mix.
• Particularly suitable for precast concrete and other high early strength requirements.
• To significantly improve the workability of site mixed and precast concrete without increasing water demand.
• To provide improved durability by increasing ultimate strengths and reducing concrete permeability.
• In screeds it reduces the water content required to give suitable workability for placing and compaction

Advantages:

• Major increases in strength at early ages without increased cement contents are of particular benefit in precast concrete, allowing earlier stripping times.
• Makes possible major reductions in water:cement ratio which allow the production of high strength concrete without excessive cement contents.
• Use in production of flowing concrete permits easier construction with quicker placing and compaction and reduced labour costs without increasing water content.
• Increased workability levels are maintained for longer than with ordinary sulphonated melamine admixtures.

Description:

• Conplast SP430 is a chloride free, superplasticising admixture based on selected sulphonated napthalene polymers.
• It is supplied as a brown solution which instantly disperses in water.
• Conplast SP430 disperses the fine particles in the concrete mix, enabling the water content of the concrete to perform more effectively.
• The very high levels of water reduction possible allow major increases in strength to be obtained.

Technical Support:

• Fosroc provides a technical advisory service for on-site assistance and advice on admixture selection, evaluation trials and dispensing equipment.
• Technical data and guidance can be provided for admixtures and other products for use with fresh and hardened concrete.

Typical Dosage:

• The optimum dosage of Conplast SP430 to meet specific requirements should always be determined by trials using the materials and conditions that will be experienced in use.
• This allows the optimisation of admixture dosage and mix design and provides a
• complete assessment of the concrete mix. Starting points for such trials, based on the primary use of the product, are to use a dosage within the normal typical ranges.
• For high strength, water reduced concrete the normal dosage range is from 0.70 to 2.00 litres/100 kg of cementitious material, including PFA, GGBFS and microsilica.
• For high workability concrete the normal dosage range is from 0.70 to 1.30 litres/100 kg of cementitious material.
• Where a combination of performance is required, such as some increase in workability combined with a reduced water content, then the whole range of dosages from 0.70 to
• 2.00 litres/100 kg of cementitious material can be considered

Additional Information:

• Delivery Time: 1-10 days as per availiblity
• Packaging Details: conplast sp 430 is supplied in 5 , 20 , 200 litre & 250kg drums.

We are actively engaged in offering a qualitative range of Conplast SP 550 Admixture for catering the diversified requirements of our clients.

Uses:

• To produce pumpable concrete
• To produce high strength, high grade concrete by substantial reduction in water resulting in low permeability and high early strength.
• To produce high workability concrete requiring little or no vibration during placing.

Advantages:

• Improved workability Easier, quicker placing and compaction.
• Increased strength Provides high early
• strength for precast concrete if water reduction is taken advantage of.
• Improved quality Denser, close textured concrete with reduced porosity and hence more durable.
• Higher cohesion Risk of segregation and bleeding minimised; thus aids pumping of concrete
• Chloride free Safe in prestressed concrete and with sulphate resisting cements and marine aggregates

Description:

• Conplast SP500 is based on Sulphonated Napthalene
• Polymers and is supplied as a brown liquid instantly dispersible in water.
• Conplast SP500 has been specially formulated to give high water reductions up to 25% without loss of workability or to produce high quality concrete of reduced permeability.

Application Instructions:
Dosage:

• Trials need to be carried out at site to determine the exact dosage of the admixture for the particular mix design and materials.
• However for normal grades of concrete a dosage from 0.5% - 1.0% by weight of cement is recommended, the dosage may be increased to 1.5% to achieve specific slump
• requirements.
• For microsilica concrete where a high amount of water reduction and slump retention are required, trials need to be carried out to arrive at the correct dosage, as the dosage may increase up to 2.0% or even up to 2.5% by weight of cement depending on mix design and performance required.

Use at other dosages:

• Dosages outside the typical ranges quoted above can be used to meet particular requirements. Contact Fosroc for advice.

Overdosage:

• An overdose of above the recommended level of admixture may result in high workability, slight increase in air entrainment and retardation of setting time.
• The ultimate strength of the concrete will not be adversely affected and will generally be higher than for normal concrete if properly placed and cured.

Additional Information:

• Delivery Time: 1-10 days depends upon availibility