Trident

• Nitotile GTA is a two-part high quality polymer based adhesive the permanent fixing of granite and marble tiles.

• Pre Packaged product requiring only direct mixing at site.
• High adhesive bond strength - Ideal for vertical and horizontal applications of granite, marble, etc.
• Excellent grab during open time
• Quick fixing - reduces labour costs
• Can be used in the interior and exterior of buildings.

• All surfaces must be sound and thoroughly cleaned beforeNitotile GTA is applied. All traces of grease and oil must be be removed.
• All loose particles of mortar, wallpaper, paint etc.,must be physically removed.
• The prepared surface must be wetted with water, prior to application of Nitotile GTA and must obtain a saturated surface dry condition.
• Nitotile GTA can be applied directly on concrete, cement screeds, cement or lime mortars provided they are strong.

• Take the liquid polymer in a suitable container and add the powder part under mixing.
• Use a slow speed drill fitted with a paddle to get a uniform lump free consistency.
• Overmixing can result in air entrainment which should be avoided.
• Water should not be added to adjust the consistency of the paste

• Nitotile GTA is applied on to the prepared substrate and spread with a serrated trowel to achieve a uniform thickness of 3 - 4mm.
• Place the tiles firmly on to the adhesive bed ensuring total contact with a twisting motion.
• Choose work areas so that the tiles can be fixed within the open time of the
• adhesive which is approx. 20 mins at 30 deg.C.
• Normally granite and marble tiles up to a thickness of 20mm can be fixed in vertical position without problem.

• Remove the excess adhesive using a damp cloth before it sets.
• Grouting of joints may be commenced 24 hours after the tiles have been fixed.

• Nitotile GTA is not recommended for overhead applications. On vertical applications, heavy slabs need proper support till appropriate grab is achieved
• Note: Nitotile GTA should not be applied on Gypsum board substrates.

• In addition to granite/marble tile adhesives, Fosroc manufactures a wide range of other products which includeconcrete admixtures, waterproofing membranes, jointsealants, grouts and anchors and specialised flooringmaterials.
• Additionally, a wide range of products specifically designed for the repair and refurbishment of damagedreinforced concrete are also available.For further information, please contact your local Fosroc office.

• Nitotile GPX is a high quality adhesive for the permanent fixing of ceramic tiles.
• It can also be used for fixing of insulating and acoustic boards based on expanded polystyrene etc. Typical uses include
• Wet areas - kitchens and bathrooms
• Tile cladding

• Tropical grade to suit Indian working conditions
• Good open wet time
• Good slip resistance
• High adhesion strength
• Water proof
• Good slip resistance
• Can be used in totally submerged conditions

• Nitotile GPX conforms to BS 5980 Class AA & B Type 1 and suitability for contact with potable water as per BS 6920 Part
• Nitotile GPX cementation powder is available in grey or white colour.

• Fosroc offers a comprehensive technical support service to specifi ers, end users and contractors.
• It is also able to offer on-site technical assistance, an AutoCAD facility and dedicated
• specifi cation assistance in locations all over the world.

• All surfaces must be sound and thoroughly clean before Nitotile
• GPX is applied. All traces of grease or oil must be removed with a chemical degreaser. All loose particles of mortar, old wallpaper, paint etc. must be physically removed.

• Nitotile GPX can be applied directly on concrete, cement screeds, and cement or lime mortar.
• Special attention must be given to new construction prior to commencing tiling.
• Tiles should not be placed on concrete or brickwork until all shrink-age movement has taken place. diluted Nitobond AR (1 : 3 with water) should be applied to the surface of the gypsum or gypsum board prior to application of Nitotile GPX.

• Nitotile GPX should be mixed with clear potable water in the ratio 4:1 by weight (4 part powder : 1 part water).
• A slow speed drill fitted with a mixing paddle is recommended for mixing.
• Add powder to water and mix until a uniform, lump-free consistency is achieved
• The total quantity of water may be slightly adjusted to achieve the required consistency.

• Nitotile GPX should be spread on the substrate to a uniform thickness of 2-3mm, and then combed horizontally with a ser-rated trowelPlace tiles firmly into adhesive bed, ensuring good contact with a twisting motion.
• Only apply to areas which can be tiled in the adhesive’s open wet time (up to 1m 2 at a time).

• It is recommended that when fixing ceramic tiles, a minimum spacing of 2mm be left around each tile

• Remove excess adhesive with a damp cloth before material has set.
• Joint grouting with Nitotile Grout* † may be commenced 24 hours after tiles have been laid

• Nitotile GPX should be removed from tools, equipment and mixers with clean water immediately after use.
• Cured material can only be removed mechanically.

• Nitotile GPX should not be used when the temperature is below 5°C and falling.
• The product should not be exposed to moving water during application.
• If any doubt arise concerning temperature or substrate conditions, consult your local Fosroc office.

Additional Information:

• Delivery Time: 1-10 DAYS AS PER AVAILIBILITY

• Nitotile MPA tile adhesive is a high quality adhesive used for the permanent fixing of tiles over smooth surfaces such as existing tiles, ceramic tiles or glass, subjected to damp and tropical conditions and for specialised applications such as tile on tile and tile-on-glass etc.

• Polymer modified - preventing of tiles not required and hence less prone to cracking of mortar
• Single component - ease of application Non toxic - User friendly application
• Excellent adhesion on smooth surfaces - Develops high adhesive bond strength
• Non shrink - excellent bond with the substrate
• Excellent work and open wet time of 2 hrs at 30 0 C
• Allows the mason to fix tiles at ease even under hot conditions
• Self cure - does not require external curing
• Forms a dense and impermeable mortar bed waterproof.

• All surfaces must be sound and thoroughly clean before
• Nitotile MPA is applied.
• All traces of grease or oil must be removed with suitable degreaser.
• All loose particles of mortar, old wallpaper, paint etc., must be physically removed.
• In case of cementation surfaces, the areas of application must be thoroughly wetted with water to obtain saturated surface dry condition.
• Incase of smooth surfaces , preventing of substrate with water is not essential.

• Nitotile MPA meets / exceeds the requirements for tensile adhesive strength of BS 5980-1980, Class AA, A & B.

• Surface Preparation-All surfaces must be sound and thoroughly clean before Nitotile MPA is applied. All traces of grease or oil must be removed with suitable degreaser.
• All loose particles of mortar, old wallpaper, paint etc., must be physically removed. In case of cementitious surfaces, the areas of application must be thoroughly wetted with water to obtain saturated surface dry condition.
• Incase of smooth surfaces , preventing of substrate with water is not essential

• Nitotile MPA should be mixed with water in the ratio of 3 : 1 by volume or 4:1 by weight. While mixing, add powder to the water to avoid lump formation
• A slow speed drill fitted with a suitable mixing paddle is recommended for mixing.
• Hand\ mixing may also be resorted to if small quantities are mixed.
• ( Note : Use of chilled water in extreme temperatures will increase open time of Nitotile MPA).

• Nitotile MPA , is spread on the substrate to a uniform thickness of 2 - 3mm.
• This is then combed horizontally with a notched trowel. The tiles are then placed firmly into the adhesive bed ensuring good contact with the mortar by a twisting motion.

• The excess material shall be removed with a damp cloth before it sets.
• Joint grouting with Nitotile Grout may be commenced 24 hours after tiles have been fixed.

• The Fosroc range of associated products include high strength cementation and epoxy grout, polyester resin based mortar for rapid presenting of steel shims to level or for direct
• bedding of small base plates.
• Also available a range of products for use in construction; viz., admixtures, curing compounds, release agents, flooring systems, repair mortars, sealants and waterproofing compounds.

• Hygienic, hard-wearing stain-free water-miscible epoxy-resintile grout., AREAS OF APPLICATION Provides a stain-free, chemical-resistant, hard-wearing,tile joint for areas like:Bathrooms, fountains and swimming pools Factories, workshops and warehouses Pharma industry, hospitals and labs Commercial and residential buildings

• To provide a hard wearing, easily cleaned, attractive tile groutwhere chemical resistance is required

• Resistant to mild chemicals and acids
• Solvent free - can be used in confined areas
• Good resistance to abrasion and impact resistance
• Attractive appearance, easily cleaned
• Available in a range of attractive colours
• Resists bacterial growth
• Hygienic - good to use in Laboratories, Hospitals and health centers
• Good to use in wet area, fountains, swimming pool, kitchen, bathroom and Sauna
• Water miscible - safe in use, no odour

• Nitotile EPW Grout is a 3 component water miscible epoxy resin tile joint filler based on new generation epoxy resin technology supplied in preweighed packs, ready for on site mixing and use.

• Nitotile EPW Grout is resistant to a comprehensive range of chemicals commonly encountered in industrial applications, few of them are listed below:-
• Water, Sea water Alkali solutions Aqueous solutions of salts Soft drinks Fruit juices Carbonated beverages Motor oils and lubricants Cosmetics and toiletries.
• Pharmaceutical products Dairy products Edible oils Medicated oils etc.

• Preparation-Joints to be grouted should be clean and free from any dust or debris.
• Mixing-The base and hardener components in a suitable container until a uniform colour is obtained.
• The filler component should then be added to the mixed liquid and blended using a slow speed drill and suitable mixingpaddle until a uniform, homogeneous mixture is obtained.

• Apply Nitotile EPW Grout with a spatula to the spaces between the tiles working the mixture into the joints and around the edges.
• Remove surplus material from the face of the tiles with a damp cloth, before material has gilled. Hardened material can only removed mechanically.

• Nitotile EPW Grout should be removed from tools, equipment with water immediately after use.
• Cured material can only be removed mechanically.

• Nitotile EPW Grout should not be used when the temperature is below 5°C and falling.
• The product should not be exposed to moving water during application.
• If any doubts arise concerning temperature or substrate conditions, consult your local Fosroc office.

Additional Information:

• Delivery Time: 1-10 days as per availblity

ConbextraGP2 isusedforprecisiongroutingwhereitisessential to withstand static and dynamic loads. Typical applications would be grouting of base plates of turbines, compressors, boiler feed pumps, bridge bearing pedastal applications & other critical applications. It can be used for anchoring a wide range of fixing i.e masts, anchor bolts and fence posts..

Free flow, high strength, non-shrink, cementitious precision grout

Additional Information:

• Delivery Time: immidiately